HK10×15×15 Needle roller bearings

Needle roller bearings, drawn cup   HK10×15×15

Demension:10×15×15 mm ,    Weight: 6.2g.

SHAPE LOCATION TOLERANCE SHOULD BE TO CURRENT STANDARD;

Outer ring fordrawncup needle roller bearings(DC type) is made of cold rolled steel strip accurately formed.Structure of DC needle roller bearings features space saving and higher capacity.They are suitable for applications with limited space and housing not hard enough to act as raceway. No requirement on axial location when the DC needle roller bearing is pressed into the housing.

Needle roller bearings, drawn cup   HK10×15×15

In most applications inner ring is not necessary for DC needle roller bearings unless shaft raceway is impractical,standard inner rings for DC to compare with open end DC needle roller bearings, close end DC needle roller bearings are good for sealing at the close end of bearings,operating temperature range for bearings grease lubricatedare 20℃ to +120℃.

1. Structures of various series of drawn cupneedlerollers
     Metricseries: HK, BK, F, FH, FY, MF, MFH,MFY
     Inch series: SCE, BCE, SCH, BCH,SN, B, BH, M, MH
     HK: Caged, with open ends
     BK: Caged, with open ends
     F : Full complement, with open ends
     FH : Full complement,withopenends(Heavy series)
     FY : Full complement, grease retained,withopenends
     MF : Full complement, with closed ends
     MFH:Fullcomplement, with closed ends(heavy series)
     MFY: Fullcomplement,withclosed ends
     SCE: Caged, with open ends
     BCE:Caged, withclosedends
     SCH: Caged, with open ends(heavy series)
     BCH: Caged,withclosed ends(heavy series)
     SN   : Full complement, greaseretained,withopen ends
     B    : Full complement, with open ends
     BH   :Fullcomplement, with open ends(heavy series)
     M    : Fullcomplement,withclosed ends
     M H: Full complement, with closedends(heavyseries)
2. Inspection the enveloping circle diameter
    The dimensional accuracy of drawn cup needle roller bearings cannot be measured before fitting
    without a ring gauge as the thin-walled outer ring can be out of round due to the manufacturing process.
    The bearings obtain the accuracy required for their correct function only when pressed into ahousing
     bore which must be manufactured with the recommended tolerance limits.
     The enveloping circle diameter can then be checked as follows:
a.   Press the bearing into a steel ring gauge(wall thickness≥20mm).The bore dimension of the ring
        gauge must correspond to that given.
b.   Measure the enveloping circle diameter with cylindrical go and no-go gauge plugs.

ShaftDia.	Part Number	Dimension			Torque Rating	LimitingSpeed		Weight
		Fw	D	C		Shaft	Housing
mm		mm			Nm	RPM		g
3	HF0306 KF	3	6.5	6	0.18	45000	8000	1
4	HF0406 KF	4	8	6	0.34	34000	8000	1
6	HF0612 KF	6	10	12	1.76	23000	13000	3
8	HF0812 KF	8	12	12	3.15	17000	12000	3.5
10	HF1012 KF	10	14	12	5.3	14000	11000	4
3	HF0306 KF R	3	6.5	6	0.06	45000	8000	1
4	HF0406 KF R	4	8	6	0.1	34000	8000	1
6	HF 0612 KF R	6	10	12	0.6	23000	13000	3
8	HF0812 KF R	8	12	12	1	17000	12000	3.5
6	HF0612 R	6	10	12	0.6	23000	13000	3
8	HF0812 R	8	12	12	1	17000	12000	3.5

Needle roller bearings, drawn cup   HK10×15×15